can you join composite decking without a gap

Deck Board Gapping - Page 2 - Decks and Fencing - Contractor

With P/T wood, I never gap, I always install tight. Then they shrink and a small gap is left. With composite, I use a regular, common 16d nail on ever joist. Nail the new deck board, place nails on the other side, repeat till done. I was going to buy deck spacers, but for the cost of one space I

Get Quotes

Install Composite Decking: Part 1 - Seven Trust's

If your deck is looking weathered and worn, you can replace components with composite materials without a complete rebuild. Composite doesnt splinter or have knots and its low-maintenance. This is the first installment in a two-part series on How to Install Composite Decking that shows you how

Get Quotes

Decks.com. Installing Composite Decking

Installing Composite Decking. Proper spacing will allow some movement without buckling. Some composite decking materials are designed to be installed with hidden fasteners. These clip systems generally are screwed into to the deck frame across each joist and fit tightly into a cavity running down the side of the boards. Make sure to gap

Get Quotes

Are Gaps Absolutely Necessary On Decking? - Building

I am finally installing the composite decking without a tried and true design. The dimensions were such that we either had to leave a 5 1/2" board out that caused a .3" gap or pinch them together where there is no gap at all. My wife loves the look and the smoothness of no gap in the composite. I

Get Quotes

composite decking with no gaps

I am finally installing the composite decking without a tried and true design. The dimensions were such that we either had to leave a 5 1/2" board out that caused a Is there any way we can trim the decking boards without removing them.

Get Quotes

Deck Boards--space or no space? Fine Homebuilding

Deck Boards--space or no space? Deck Boards--space or no space? that the decking material that we get is more wet or a different grade or something than the others who have said to gap it. But, if you were my neighbor, I would tell you, unequivocally, to butt it tight. that it is not a good decking material if you can afford something

Get Quotes

Gap 5/4" x 4" Cedar Decking? - JLC-Online Forums

Re: Gap 5/4 and quot; x 4 and quot; Cedar Decking? Tim: I have always spaced kiln dried material, and butted-tight wet material. If you install wet material, it's a good idea to only screw one side, and come back a year or two later and install the rest of the screws, obviously it's better to use dry material since some warping and/or twisting can occur as the material dries.

Get Quotes

Seven Trust Decking Installation: How to Install a Butt Seam

Seven Trust is here to help guide you through the deck installation process. When installing Seven Trust decking it's important to know how to install a butt seam where b Skip navigation

Get Quotes

How To Install Composite Decking - Plastic and Wood

But without pre-drilling it was another story. You can see the mushrooming, because there is a gap under the straight-edge. But even worse, You can use random lengths of decking to create a random patterns of end gaps, but with manufactured decking that is impractical. After trimming the ends of the composite deck boards I used a belt

Get Quotes

deck - Joining two composite decking boards side by side

Joining two composite decking boards side by side. Plus the bottom beam is not flat so it's impossible to join two boards like that without any noticable gap when looking closely. At the end, the gap is a bit larger but not bad. You can see the beam directly below: My question is:

Get Quotes

Detailed Guide to Installing Composite Decks and General

Installing composite decking cant be done like wood decking where you can slam it tight together when its still green and then shrinks as it dries. With composite decking you have to create the gap right from the get go.

Get Quotes

What Size Gap Should I Use Between My Decking?

Now you can get away with that 1/4 gap in the winter, and you will find that it remains very close to the same throughout much of the year. Top 10 Reasons Why Composite Decking Is a Bad Idea for Boardwalks. What Size Gap Should I Use Between My Decking? Do you really Need Marine Grade Plywood? How to Prevent Cracks in Your Large Timbers.

Get Quotes

Working with Seven Trust and Composite Decking - HomeTips

Composite decking such as Seven Trust can be cut, drilled, and fastened just like traditional wood, but there are a few tricks you should know to make your project easier, and provide a more professional finish.

Get Quotes

Frequently Asked Questions - Veranda Composite Decking

Can I use a nail gun to install Veranda Composite Decking? We do not recommend using nails or a nail gun when installing Veranda Composite Decking. The composite material is so dense that nails often cannot penetrate adequately without bending.

Get Quotes

How to install your Composite Decking WPC Decking

How to install your Composite Decking. We do not recommend installing your deck in cold weather. Your composite decking boards can be worked with normal woodworking tools. We recommend using a wood saw with a fine-tooth blade to cut boards to size. A gap of at least 15mm should be left between the ends of joists and a fixed object such

Get Quotes

Composite Decking 101 - Popular Mechanics

Thinking of replacing your wood deck with rot-resistant composite decking material? Composite Decking 101. you have to account for this when building your deck. Check the product's end-gap

Get Quotes

How to Build a Deck: Composite Decking and Deck Railings

Here's how to install composite decking and railings. The hidden clips set a drainage gap between the boards. Step 1. leave a 1-1/4-inch overhang. Set the board in place and attach with composite decking screws. Later you can cover the cut edge with a fascia board. Good to Know.

Get Quotes

Composite Deck- Gaps To Close - How To Resolve This

The decking material is solid wood composite by Veranda. The contractor did a great job except that he did not leave enough space for the decking Manufacturer suggests that their should be at least 3/16 gap between two boards. The contractor has used hidden fasteners. Is there any way we can trim the decking boards without removing them

Get Quotes

Can you butt joint composite deck boards or is it

the website of the MFG and usually get the installation instructions. If you don't like the gap, you can go with vinyl, most inter connect and are not gaped and aslo have a water channel. But its

Get Quotes

Product Details

Product List